The 3.4 miles (5.5 km) was completed at 10:37 EST. Before rolling out to the launch pad, engineers at Kennedy Space Center had an extended preparation time to get Endeavour ready to move to the launch pad due to the unusually cold weather. The process started at 04:13 EST on January 6, 2010. Roll over began at 13:00 EST and was completed 1 hour and 5 minutes later at 14:05 EST.Įndeavour moved from the Vehicle Assembly Building to launch pad 39A. Space Shuttle Endeavour was moved from her hangar in the Orbiter Processing Facility 2 to the Vehicle Assembly Building High bay 1 on December 11, 2009. Shuttle processing Endeavour arrives at Pad 39A on January 6, 2010, for the STS 130 mission. Cupola is seen on top with its protective launch cover still attached. PMA-3 is moved to the end of Tranquility. It is also known as Node 3, and was named by a NASA poll as Tranquility. It arrived at the Kennedy Space Center Space Station Processing Facility on May 21, 2009. Tranquility was manufactured at the Thales Alenia Space factory in Turin, Italy, and transported by aircraft to Florida. STS-130 carried Tranquility and the Cupola to the International Space Station. Endeavour launched at 04:14 EST (09:14 UTC) on Febru and landed at 22:22 EST on February 21, 2010, on runway 15 at the Kennedy Space Center's Shuttle Landing Facility. Space Shuttle Endeavour's primary payloads were the Tranquility module and the Cupola, a robotic control station with six windows around its sides and another in the center, providing a 360-degree view around the station. Several test tiles were placed on orbiter’s base heat shield between three main engines.STS-130 ( ISS assembly flight 20A) was a NASA Space Shuttle mission to the International Space Station (ISS). Mission also marked first flight of Toughened Uni-Piece Fibrous Insulation, known as TUFI, an improved thermal protection tile. Middeck experiments included Visual Function Tester-4 (VFT-4), Space Tissue Loss-4 and -5 and Shuttle Amateur Radio Experiment (SAREX). It produced crystals and thin films through physical vapor transportation. Get-Away Special (GAS) experiments were sponsored by New Mexico State University, Matra Marconi Space (France), and the Society of Japanese Aerospace Companies.Ĭonsortium for Materials Development in Space Complex Autonomous Payload-IV (CONCAP IV), carried in GAS hardware in the payload bay, was developed by the University of Alabama-Huntsville. The MAPS experiment measured the global distribution of carbon monoxide in the troposphere, or lower atmosphere. Thirteen countries were represented in the project with 49 principal investigators and more than 100 scientists, coordinated by the Jet Propulsion Laboratory (JPL). More than 400 sites were imaged, including 19 primary observation sites (supersites) in Brazil, Michigan, North Carolina and Central Europe. SIR-C/X-SAR covered approximately 38.5 million miles of the Earth, the equivalent of 20 percent of the planet. The German Space Agency (DARA) and the Italian Space Agency (ASI) provided the X-SAR instrument. SRL-1 included the Spaceborne Imaging Radar-C and the X-band Synthetic Aperture Radar (SIR-C/X-SAR) and an atmospheric instrument called Measurement of Air Pollution from Satellites (MAPS). Primary payload was the Space Radar Laboratory (SRL-1), located in payload bay activated by crew and operated by teams on ground. Launch on April 8 scrubbed due to weather, high crosswinds and low clouds at Shuttle Landing Facility (SLF) and clouds at launch pad. Launch originally set for April 7 was postponed at the T-27 hour mark for one day to allow for additional inspections of metallic vanes in the space shuttle main engine (SSME) high pressure oxidizer preburner pumps. Jones, Mission Specialist Launch Highlights Mission Duration: 11 days, 5 hours, 49 minutes, 30 seconds Landing Site: Edwards Air Force Base, Calif.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |